It is currently Fri 01. Nov 2024 0:54:07

All times are UTC + 1 hour





Post new topic Reply to topic  [ 16 posts ]  Go to page Previous  1, 2
  Print view Previous topic | Next topic 
Author Message
 Post subject: Re: Best reciever
PostPosted: Fri 19. May 2023 16:44:19 
Offline

Joined: Thu 13. Apr 2023 12:01:25
Posts: 18
As requested. ImageImageImageImageImageImageImageImageImage

Sent from my LYA-L29 using Tapatalk


Top
 Profile  
 
 Post subject: Re: Best reciever
PostPosted: Fri 19. May 2023 17:24:36 
Offline

Joined: Sun 08. Jan 2023 14:32:43
Posts: 274
I can't understand this number
however it must be 90 with a margin of 4 numbers.
Attachment:
158b67900e7b7932480e027ec7dfc1681.jpg
158b67900e7b7932480e027ec7dfc1681.jpg [ 60.18 KiB | Viewed 286 times ]


From what I see there are two possible causes.
1 and I'm sure that's the problem, your 0 as I thought is not configured well.
maintaining position try to hold that position that you configured and this configuration tends to move the model

2 the vibrations cause the problem

I have to ask you this question, in your radio trim and subtrim are at 0?

PS
it's not set up right , the servo horn are not straight.
I can tell you step by step how to do it, but I think these are things you already know.
Why elevator is it so inclined?
the other two servants are not at 90, but slightly down.
swashplate not is level.
and I believe that the tail it is not set well, you have too much subtrim (but that has nothing to do with your problem, it's another thing)
Geolink if you are almost 90 is ok, so the problem is NOT THE GEOLINK

before putting hands give me confirmation if you have 90° in geolink.
how many vibrations do you have?
and that you don't use trim and subtrim on your radio.

this is servo 90°
Attachment:
120230514_201859.jpg
120230514_201859.jpg [ 47.6 KiB | Viewed 285 times ]


Top
 Profile  
 
 Post subject: Re: Best reciever
PostPosted: Sat 20. May 2023 9:01:45 
Offline

Joined: Sun 08. Jan 2023 14:32:43
Posts: 274
do these things:
servo-subtrim tuning
move slider ch 1 2 3 to have this
https://www.spirit-system.com/phpBB3/download/file.php?id=4827&t=1
with the servant in this mode you must have this (follow the red lines)
Attachment:
220230518_195908.jpg
220230518_195908.jpg [ 210.73 KiB | Viewed 274 times ]

this situation you must have it turning the rotor 360 degrees, always the same
and In the end you must have this situation
https://youtu.be/x1aFSfl1wsk
Obviously put the blade in one point and measure the degrees, after at the same point put the other blade and measure, you must have the same degrees, this is for tracking
PS
note on the tail not is perfect I have to fix it again


Top
 Profile  
 
 Post subject: Re: Best reciever
PostPosted: Mon 22. May 2023 12:36:19 
Offline

Joined: Thu 13. Apr 2023 12:01:25
Posts: 18
Thank you i will recheck my setup. I do find with the 450 pro getting the servo exactly 90° by eye difficult. Is there a trick or tool to get it 100% correct.

I have run calibration for the geolink compass but with my heli at north on the hand held compass the geolink is stating 84°

Is there a certain tolerance? I can manually adjust in settings but only by +-45°

Can the compass calibration be done wrong or is it pretty fool proof?

Thank you for your help by the way this is all new territory for me.

Sent from my LYA-L29 using Tapatalk


Top
 Profile  
 
 Post subject: Re: Best reciever
PostPosted: Mon 22. May 2023 12:43:00 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12433
Hello,

84° is still acceptable, so it should be OK.
Calibration can't be done entirely wrong, but it could be done more precisely by moving to angles where LED light is flashing more frequently - with more gentle movement around to make sure GeoLink's LED will not flash anymore there.

If you will use 6° degrees correction then it will be perfect very likely. However it is easy to see with Position Hold. If model will be really steady then calibration is good.

_________________
Spirit System developer


Top
 Profile  
 
 Post subject: Re: Best reciever
PostPosted: Thu 25. May 2023 14:21:15 
Offline

Joined: Sun 08. Jan 2023 14:32:43
Posts: 274
when I calibrated the compass I had some doubts.
When I made a tight movement I noticed the light changing
and then after I widened the movement.
But then I arrived at a certain point where the calibration never ended.
And it took me a long time.
I believe that I didn't understand good 100% all circular movements to do.
How the black lines of the circle of this image (I only made one to get the idea)
Attachment:
compasscalibration.jpg
compasscalibration.jpg [ 194.52 KiB | Viewed 215 times ]

I move making a small circle how la prima linea nera, after movement how the second black line ecc ecc.
But then never finished calibration.
Exactly to complete compass calibration all the movements to do Which ones are they?
i remember i was at least 20 minutes when instead it had to be completed in a few minutes


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 16 posts ]  Go to page Previous  1, 2

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 7 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .