It is currently Fri 01. Nov 2024 0:53:46

All times are UTC + 1 hour





Post new topic Reply to topic  [ 5 posts ] 
  Print view Previous topic | Next topic 
Author Message
PostPosted: Mon 18. Apr 2022 19:42:48 
Offline

Joined: Wed 24. Jun 2015 4:03:28
Posts: 119
The manual states: RPM Sensor data are too noisy:

RPM readout is very unstable and are oscilating more than +/- 100 RPM. Data from the sensor are unusable for the Governor. Use additional shielding and mount a ferite rings. Increase value of the RPM Sensor filter parameter in the Expert settings

If the "rpm sensor data are too noisy" message in the log is when the RPM's oscillate +/- 100 rpm's does that mean we should tune the governor first before trying to reduce noise?


Attachments:
spirit-log-2022-04-18-141307.pdf [70.11 KiB]
Downloaded 33 times
Top
 Profile  
 
PostPosted: Tue 19. Apr 2022 9:28:52 
Offline

Joined: Fri 20. Aug 2021 6:12:26
Posts: 61
It's always best to reduce electrical/mechanical noise first. More filtering adds more delay and reduces effectivness of PID controllers


Top
 Profile  
 
PostPosted: Tue 19. Apr 2022 13:32:09 
Offline

Joined: Wed 24. Jun 2015 4:03:28
Posts: 119
Hey jasc,
While I agree it's always better to reduce noise to minimize efforts of filtering downstream. The "Noisy Sensor Data" actually means something more than just noise and this is what I want to understand. As mentioned above, according to the manual, any variation of over or under 100 rpms will create a record in the log of "noisy Sensor Data".

So there are three meaning to this "noisy sensor data": an abundance of noise, as well there is a potential for bad governor settings, as well as poor engine tuning. All of these conditions will result in "noisy sensor data" in the log.

Another natural conclusion then is that the log record of "noisy sensor data" may in fact not have anything to do with EMF noise or any kind of electrical interference.

Just looking for clarity if there is any.


Top
 Profile  
 
PostPosted: Sat 23. Apr 2022 15:40:05 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12433
Hello,

noisy sensor data mean that the reading is unstable.
This can be also caused by too high gains of the Governor.
In other words, if sensor is working well but governor is tuned badly, you can get the same message.

If you are uncertain, it can be helpful to hover the model with the lowest possible gains or at least with default governor gains.

Usually when sensor is working incorrectly there are problems with Governor engaging. So that it will engage, not engage or maintain wrong RPM. Each flight you will get different results.

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Sun 01. May 2022 2:43:48 
Offline

Joined: Wed 24. Jun 2015 4:03:28
Posts: 119
Tomas,
Will a noisy rod end inside the engine also cause an unstable rpm sensor? as in a log record of Noisy Sensor Data.

Scott


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC + 1 hour


Who is online

Users browsing this forum: Renzo and 11 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .