It is currently Thu 28. Mar 2024 21:47:01

All times are UTC + 1 hour





Post new topic Reply to topic  [ 82 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6, 7 ... 9  Next
  Print view Previous topic | Next topic 
Author Message
PostPosted: Sun 18. Jul 2021 19:01:10 
Offline

Joined: Wed 11. Nov 2020 0:10:39
Posts: 28
ZeXx86 wrote:
We hope to include this in 3.3.1. Thank you for your patience


Did it get included? I tried flashing 3.3.1 to my Spirit GT now but I can't see it. I also have problems with using Sbus from crossfire now (no special cable) but on my Spirit II units this isn't a problem. Could this be due to spirit GT having some built in logic for inverted/not inverted sbus? I can select N.I.Sbus in my crossfire module.

edit: I can get it sorta working but there def is something wrong now with the channels. I got ch1 throttle, 2 ail, 3 elevator, 4 rudder, 5 gyro, 6pitch. In spirit now I have to set ch2 throttle, ch3 ail, ch1 ele, ch4 rud, ch5 gyro, ch6 pitch. The aileron is maxing out at 118% at mid stick but it works in left direction. Pitch I have to set to -51 (-100 is normal) to get it to -100 in spirit settings and I can't get it higher than 82% on max stick output. So it's not possible to fly it without aileron atm.

edit2: If I abandoned the wizzard and rebooted the spirit it somehow sorted out the channel mess again. Now aileron and pitch behaves like it should. I guess I just won't be able to run the wizzard then but it's better then not beeing able to fly it :)


Top
 Profile  
 
PostPosted: Mon 19. Jul 2021 15:38:04 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12213
It was not included yet unfortunately. There are so many pilot requests and so many questions we are unable to make it working yet. We have to do everything at the same time, because then people are not satisfied without responding them.

Spirit GT should work in the same way as Spirit 2. Setup Wizard should not make a difference, but Futaba S.BUS must be selected to make it work.
Channel mapping should be at default - same for all Spirit units.

After reboot channel centers are calculated again. Maybe there was some channel out of range - default OpenTX settings are that it is out of range. So all channels must be configured to have +/- 87% travel range.

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Mon 19. Jul 2021 19:34:36 
Offline

Joined: Wed 11. Nov 2020 0:10:39
Posts: 28
Ok. No problem, was just curious if I missed it somehow.


Weird that I haven't had this issue with my spirit 2 yet but I will try as you suggested and run the wizzard with channels set at 87% of travel range. I think I'm down with 83% or around that to get -100 to 100 in spirit now but I always start fresh with transmitter at -100 to 100 so it would explain my issue. Futaba S-bus was set and it did work to some degree since some of the channels was ok.


Top
 Profile  
 
PostPosted: Fri 06. Aug 2021 3:15:52 
Offline

Joined: Fri 25. Jun 2021 4:21:41
Posts: 8
Is it safe to assume that I will need the FrSky integration cable for ųspirit if/when this feature is available?


Top
 Profile  
 
PostPosted: Tue 10. Aug 2021 9:32:07 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12213
Hello,

it is very likely that no special cable will be needed for TBS Crossfire.
Fortunately window for adding the support is free, so I feel it will end up in 3.3 almost certainly.

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Thu 19. Aug 2021 11:07:51 
Offline

Joined: Sun 23. May 2021 9:13:35
Posts: 9
Is TBS working incl. telemetrie?
Thinking about using my Mambo for the next heli ;)


Top
 Profile  
 
PostPosted: Fri 20. Aug 2021 6:21:57 
Offline

Joined: Fri 20. Aug 2021 6:12:26
Posts: 61
Your working on crsf integration?!
THAT IS GREAT

Hope to see it soon !

TBS made some big improvements with the new CRSFv3 radio link dropping to only few ms latency. And ExpressLRS is even faster but also using crsf protocol between receiver and flight controller and that for a fraction of the price of all commercial systems

See here https://theuavtech.com/rc-control-link-modules/


Top
 Profile  
 
PostPosted: Sat 04. Sep 2021 7:21:49 
Offline

Joined: Fri 20. Aug 2021 6:12:26
Posts: 61
Could you please give an update on this


Top
 Profile  
 
PostPosted: Sat 04. Sep 2021 9:33:07 
Offline
User avatar

Joined: Mon 23. Aug 2021 22:21:16
Posts: 25
Exciting news! Can’t wait

tx16s (+/- 83%) + tbs tx micro module + tbs rx diversity nano here.

Seems like TBS has some kind of cooperation with Radiomaster since they even sell tx16s in their webstore.


Top
 Profile  
 
PostPosted: Tue 07. Sep 2021 7:09:00 
Offline

Joined: Fri 20. Aug 2021 6:12:26
Posts: 61
ZeXx86 wrote:
Hello,

it is very likely that no special cable will be needed for TBS Crossfire.
Fortunately window for adding the support is free, so I feel it will end up in 3.3 almost certainly.


Can you give a new timeline ?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 82 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6, 7 ... 9  Next

All times are UTC + 1 hour


Who is online

Users browsing this forum: Bing [Bot] and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .