It is currently Tue 15. Oct 2024 23:36:31

All times are UTC + 1 hour





Post new topic Reply to topic  [ 12 posts ]  Go to page 1, 2  Next
  Print view Previous topic | Next topic 
Author Message
PostPosted: Thu 12. Oct 2023 15:21:25 
Offline

Joined: Mon 03. Jan 2022 18:08:45
Posts: 59
Hi i have a goblin 570 tail locks and hold good no wagging no any problem during hovering. When i fly fast and i do right turn then tha tail is doing fast overshooting Can someone give me some tips for that issue? Thanks


Top
 Profile  
 
PostPosted: Thu 12. Oct 2023 20:42:01 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12401
What is your Pitouette consistency and Rudder delay?

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Fri 13. Oct 2023 6:14:28 
Offline

Joined: Mon 03. Jan 2022 18:08:45
Posts: 59
Hi the rudder delay is 2 and pirouette consistency is 177. My rudder servo is kst bls805x
Some extra infos, my gyro gain is at 70% i try 80% but now changes
Rudder dynamic is 6. Thanks


Top
 Profile  
 
PostPosted: Fri 13. Oct 2023 10:59:42 
Offline

Joined: Mon 03. Jan 2022 18:08:45
Posts: 59
Any tips please?


Top
 Profile  
 
PostPosted: Fri 13. Oct 2023 11:03:59 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12401
Hello,

your tail servo is little bit specific and require different servo arm length.
Can you also let me know what are your current Rudder End-point values?
Changing Rudder servo arm length can help a lot. Your settings looks good. You can set Rudder Delay to 0.

Also make sure that tail slider (if present) is not touching the push rod or even that push rod is not bent there.
Any friction there will make tail performance worse.

Decreasing Gyro gain will help for sure too. Then if needed, you can set Rudder Revomix to 2-3. Revomix shouldn't be needed normally in any case, but can be helpful when using lower Gyro Gain.

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Fri 13. Oct 2023 11:45:29 
Offline

Joined: Mon 03. Jan 2022 18:08:45
Posts: 59
Hi the tail end points are both 90


Top
 Profile  
 
PostPosted: Fri 13. Oct 2023 11:49:20 
Offline

Joined: Mon 03. Jan 2022 18:08:45
Posts: 59
Do you think that i must reduce a bit rudder end point to the side that makes overshooting? So to decrease litle the angle of tail blades?


Top
 Profile  
 
PostPosted: Fri 13. Oct 2023 11:51:38 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12401
You can try to make rudder servo arm shorter if possible. Then please readjust rudder end-points.

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Fri 13. Oct 2023 11:54:55 
Offline

Joined: Mon 03. Jan 2022 18:08:45
Posts: 59
Ok i will move ball link one hole up but what you think is godd value for end points, 90 -100 is ok?


Top
 Profile  
 
PostPosted: Fri 13. Oct 2023 11:55:20 
Offline

Joined: Mon 03. Jan 2022 18:08:45
Posts: 59
Ok i will move ball link one hole up but what you think is godd value for end points, 90 -100 is ok?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 12 posts ]  Go to page 1, 2  Next

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .