Spirit System
https://www.spirit-system.com/phpBB3/

Need Channel for Landing Gear
https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=5909		 Page 1 of 1
Author:  doingmainestuff [ Fri 15. Dec 2023 2:33:30 ]
Post subject:  Need Channel for Landing Gear
I built a scale heli, and I'm using the Spirit GT.

How can I free up a channel for my electric retracts? I bought a Spektrum AR6610T, which is bound and working. But, for my life, I cannot figure out how to free up a channel for the gear.

The Gyro is using the gear channel by default. The BING/PROG port on the AR6610T is connected to the RUD/ELE on the GT. So, I have five free channels on the AR6610T I was hoping to use for the gear.

Tips? Tricks?

Attachments:
File comment: I have my AR6610T wired precisely like this.
1200px-Ar6610t-wiring.jpg
1200px-Ar6610t-wiring.jpg [ 172.71 KiB | Viewed 279 times ]
Author:  senaka [ Fri 15. Dec 2023 8:51:40 ]
Post subject:  Re: Need Channel for Landing Gear
You may need to re assign the switch you like to use for the retracts to another free channel. This should be done on the transmitter this is how I do it on FrSKY ethos transmitter.
Author:  Mattes61 [ Fri 15. Dec 2023 8:54:41 ]
Post subject:  Re: Need Channel for Landing Gear
Hello,
one trick you can do is to deactivate the gyro-Channel in Spirit Settings and make your settings directly in the FBL -
second trick is to use under special functions an dedicated output to switch your gear - I am not shure there are two possible channels which can be taken, please look in the list...

Attachment:
Info_001.jpg
Info_001.jpg [ 39.69 KiB | Viewed 263 times ]
Author:  ZeXx86 [ Fri 15. Dec 2023 8:55:21 ]
Post subject:  Re: Need Channel for Landing Gear
Assign F: Output to AUX2 in the channels window and select a free channel there. You can use for example channel 10. Then connect landing gear to AUX2 port.
Author:  doingmainestuff [ Fri 15. Dec 2023 13:56:09 ]
Post subject:  Re: Need Channel for Landing Gear
ZeXx86 wrote:
Assign F: Output to AUX2 in the channels window and select a free channel there. You can use for example channel 10. Then connect landing gear to AUX2 port.


Can I do this even with the BEC cable plugged in to AUX2?
Author:  ZeXx86 [ Fri 15. Dec 2023 14:01:53 ]
Post subject:  Re: Need Channel for Landing Gear
Yes, or you can use CH0 port as well.
Author:  doingmainestuff [ Fri 15. Dec 2023 15:06:57 ]
Post subject:  Re: Need Channel for Landing Gear
ZeXx86 wrote:
Yes, or you can use CH0 port as well.


I tried CH0 and mapped it in "Channels." But, it won't toggle. It simply says (State 1) and on. What am I doing wrong?
Author:  toni67 [ Fri 15. Dec 2023 15:13:18 ]
Post subject:  Re: Need Channel for Landing Gear
doingmainestuff wrote:
ZeXx86 wrote:
Yes, or you can use CH0 port as well.


I tried CH0 and mapped it in "Channels." But, it won't toggle. It simply says (State 1) and on. What am I doing wrong?


ZeXx86 meant: BEC to CH0... ;)
Author:  ZeXx86 [ Fri 15. Dec 2023 15:17:34 ]
Post subject:  Re: Need Channel for Landing Gear
I meant F: Output to CH0 instead of Output to AUX2 if it is unused.
But both should work, also BEC at CH0.

There is nothing else needed. It should work immediately with a servo.
You can also assign Throttle function to Channel 1. This should do the trick.
Author:  doingmainestuff [ Sat 16. Dec 2023 13:51:10 ]
Post subject:  Re: Need Channel for Landing Gear
ZeXx86 wrote:
I meant F: Output to CH0 instead of Output to AUX2 if it is unused.
But both should work, also BEC at CH0.

There is nothing else needed. It should work immediately with a servo.
You can also assign Throttle function to Channel 1. This should do the trick.


When I set Output to AUX2, I don't see the usual "Value 0/1"; I see "State: On (1)." In this mode, the value doesn't toggle like other channels.

I got the gear to work by disabling and using the Gyro channel instead. But I'd like to learn the way you suggested, too.

What have I done wrong?

Attachments:
IMG_0171.jpg
IMG_0171.jpg [ 1.71 MiB | Viewed 224 times ]
Page 1 of 1 All times are UTC + 1 hour
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/