It is currently Mon 13. May 2024 3:20:50

All times are UTC + 1 hour





Post new topic Reply to topic  [ 6 posts ] 
  Print view Previous topic | Next topic 
Author Message
 Post subject: Sufficient Sat 'Count' ?
PostPosted: Fri 18. Aug 2023 6:50:24 
Offline

Joined: Thu 21. Apr 2022 1:34:02
Posts: 56
I just tested Telemetry Sat 'Count' under very difficult circumstances, between two 3-storey buildings, only about 10 - 15M apart.
Here in Melbourne, Australia at about 1500 local my radio counted 12.
What is considered a 'safe' number to trust the GPS guidance.
Obviously, I am normally flying in a much more open environment, and from Jeti GPS systems consider 12 to be a 'good' number.
What does everybody think?
Regards,
Andy


Top
 Profile  
 
PostPosted: Sat 19. Aug 2023 14:56:51 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12248
With GeoLink v1 it is 12.
With GeoLink v2 it is 16.

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Sun 20. Aug 2023 7:33:10 
Offline

Joined: Thu 21. Apr 2022 1:34:02
Posts: 56
Thanks ZeXx86,
I had the Logo 700 maintain a pretty accurate position hold today with 12 satellites counted.
The position hold precision was pretty good at probably better than 20cm, although the corrections were a little jerky (choppy).
This was on the default GPS settings. Should I slightly reduce the horizontal gain a bit?
Andy


Top
 Profile  
 
PostPosted: Tue 22. Aug 2023 0:00:28 
Offline

Joined: Thu 21. Apr 2022 1:34:02
Posts: 56
Yesterday, in the same very tight spot between the houses, I managed to acquire 16 satellites - very impressed.
I have reduced the horizontal gain down to 85% and corrected the compass to 90 degrees - (North). I am keen to see how this improves things with the slightly jerky position hold corrections!
Andy


Top
 Profile  
 
PostPosted: Fri 25. Aug 2023 9:15:37 
Offline

Joined: Thu 21. Apr 2022 1:34:02
Posts: 56
After reducing the horizontal gain to 80%, the helicopter failed to maintain position at all!
At 110% it acted in the same way as 90% with jerky corrections.
Any suggestions to smooth this position-hold correction, please?
This was not in coaxial mode! Maybe needs to be?
Andy


Top
 Profile  
 
PostPosted: Fri 25. Aug 2023 9:55:59 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12248
It should maintain position even with the lowest settings. I am not sure what is your configuration, so it is hard to guess.
In any case you can safely set the lowest correction.

Make sure that Integration menu was closed properly by the Close menu.

_________________
Spirit System developer


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 69 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .