Yes for real time logging and file attached...
| Attachments: |
Rufus E755.4ds [255 Bytes]
Downloaded 24 times |
| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| GT initializing https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=4761 |
Page 1 of 4 |
| Author: | 10x [ Sat 10. Jul 2021 19:38:47 ] |
| Post subject: | GT initializing |
Hello Tomas Slight problem with my GT. The 1st time i connect the receiver battery some times the GT just puts the blue led on with no flash and does not initalize and nothing works. If i disconnect the battery and plug in right away the led flashes and it all works ok....If i carry on conecting and disconecting battery it initializes evey time, but if i leave it for a while it goes back to not starting. If it is starting ok all works well and flies good. Just a bit concerned....Jeti DS12 with Rex3 and Spirit GT... Regards Adrian |
|
| Author: | pho [ Sat 10. Jul 2021 20:20:08 ] |
| Post subject: | Re: GT initializing |
I have observed exactly the same. Ds14, Rex3 Sometimes it takes 2 Power up cycles to init GT. If it is up... everything works fine BR Philip |
|
| Author: | HeliMLM [ Sat 10. Jul 2021 20:38:56 ] |
| Post subject: | Re: GT initializing |
Hi, how is the setup of the Rex3? |
|
| Author: | heri [ Sat 10. Jul 2021 21:37:01 ] |
| Post subject: | Re: GT initializing |
Hello, i have the same problem with my futaba t14sg via s-bus. Heri |
|
| Author: | 10x [ Sat 10. Jul 2021 22:10:52 ] |
| Post subject: | Re: GT initializing |
HeliMLM wrote: Hi, how is the setup of the Rex3? Output Period = 17ms ppm/udi mode = direct fail safe delay = 1.5s 2/E1 = exbus Not sure if you mean any other details.... Just to add i am using life battery for receiver/spirit... |
|
| Author: | HeliMLM [ Sun 11. Jul 2021 9:55:20 ] |
| Post subject: | Re: GT initializing |
i've not seen this happen to my GT so far. i am using 10ms and failsafe off (= to be done by Spirit unit) on all my Spirit units. i powered it either by 4xEneloop or 2s LiPo on bench and later directly out of YGE Bec (7.7V). did you check the Spirit log when this happened? there should be some entry telling "why" it is not initializing... (and maybe: is Jeti telemetry already working correctly at this time? receiver correctly bound and responding? Spirit telemetry items?) |
|
| Author: | 10x [ Sun 11. Jul 2021 10:25:00 ] |
| Post subject: | Re: GT initializing |
HeliMLM wrote: i've not seen this happen to my GT so far. i am using 10ms and failsafe off (= to be done by Spirit unit) on all my Spirit units. i powered it either by 4xEneloop or 2s LiPo on bench and later directly out of YGE Bec (7.7V). did you check the Spirit log when this happened? there should be some entry telling "why" it is not initializing... (and maybe: is Jeti telemetry already working correctly at this time? receiver correctly bound and responding? Spirit telemetry items?) I have now changed rx to 10ms, telementry from jeti rx all working but not from GT, Will wait awhile and retest, when starts up ok log reports all good... |
|
| Author: | rotorhead51 [ Sun 11. Jul 2021 14:53:39 ] |
| Post subject: | Re: GT initializing |
I have the same issue as well! Futaba 18SZ, S-Bus with R7008SB receiver, running off a 2S lipo. |
|
| Author: | ZeXx86 [ Mon 12. Jul 2021 7:44:27 ] |
| Post subject: | Re: GT initializing |
Can you let me know if you have RealTime logging enabled? Also you can share your settings file please so we can find the problem. |
|
| Author: | 10x [ Mon 12. Jul 2021 8:12:28 ] | ||
| Post subject: | Re: GT initializing | ||
Yes for real time logging and file attached...
|
|||
| Page 1 of 4 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|