Spirit System
https://www.spirit-system.com/phpBB3/

Adjusting Gyro Dx6i
https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=4452		 Page 1 of 1
Author:  Paula [ Wed 23. Dec 2020 14:50:00 ]
Post subject:  Adjusting Gyro Dx6i
Hi.
This is probably a really dumb question but....
I've set up my Spirit on my Trex 450l following the manual and the wizard and it's doing everything I think it should.
I've got Stabi on my 5th channel, but i'm unsure about this bit.
My question is where do i adjust my Gyro now? Do i still do it in the TX under Gyro? My plan is get that set right and then set that in the Spirit so I can free up that channel for Rescue..
The numbers in diagnosis don't match the numbers in my TX and this is confusing me too.
EG in TX GYRO = 69% in Spirit = -50%
TX GYRO = 315 in Spirit = +50%.

Hope that makes sense.

Attachments:
Screenshot 2020-12-23 at 13.34.38.png
Screenshot 2020-12-23 at 13.34.38.png [ 49.43 KiB | Viewed 303 times ]
Screenshot 2020-12-23 at 13.34.27.png
Screenshot 2020-12-23 at 13.34.27.png [ 74.15 KiB | Viewed 303 times ]
Screenshot 2020-12-23 at 13.34.13.png
Screenshot 2020-12-23 at 13.34.13.png [ 66.65 KiB | Viewed 303 times ]
Author:  Paula [ Wed 23. Dec 2020 14:51:23 ]
Post subject:  Re: Adjusting Gyro Dx6i
Here's my TX settings

Attachments:
IMG_0281.jpeg
IMG_0281.jpeg [ 3.21 MiB | Viewed 269 times ]
IMG_0280.jpeg
IMG_0280.jpeg [ 2.86 MiB | Viewed 269 times ]
Author:  latjo-k [ Thu 24. Dec 2020 12:03:25 ]
Post subject:  Re: Adjusting Gyro Dx6i
HI
First you have to check that the gyrochannel 5 is not rev,increce the value in tx and look in general
tab that the numbers increces there to.Then you use a switch assign to a mix in tx and mix in a -number to the gyrochannel 5,so when you hit the resque switch the the gyro value
changes from + to -,that activates the resque in Spirit.
http://manual.spirit-system.com/index.p ... #STABI_TAB
//Latjo
Author:  Paula [ Thu 24. Dec 2020 12:39:23 ]
Post subject:  Re: Adjusting Gyro Dx6i
latjo-k wrote:
HI
First you have to check that the gyrochannel 5 is not rev,increce the value in tx and look in general
tab that the numbers increces there to.Then you use a switch assign to a mix in tx and mix in a -number to the gyrochannel 5,so when you hit the resque switch the the gyro value
changes from + to -,that activates the resque in Spirit.
http://manual.spirit-system.com/index.p ... #STABI_TAB
//Latjo


Ok my GYRO was reversed. I have changed that now. When i increase GYRO in the TX the number increases in the Diagnostic tab. When I have the GYRO at 31% in the TX it is -50 in the Diagnostic tab and the Stabilisation says Engaged.
Author:  Paula [ Thu 24. Dec 2020 12:57:21 ]
Post subject:  Re: Adjusting Gyro Dx6i
When it says Configured (Gyro Gain) does that mean i can adjust the Gyro from my TX?
Author:  latjo-k [ Thu 24. Dec 2020 14:53:41 ]
Post subject:  Re: Adjusting Gyro Dx6i
Paula wrote:
latjo-k wrote:
HI
First you have to check that the gyrochannel 5 is not rev,increce the value in tx and look in general
tab that the numbers increces there to.Then you use a switch assign to a mix in tx and mix in a -number to the gyrochannel 5,so when you hit the resque switch the the gyro value
changes from + to -,that activates the resque in Spirit.
http://manual.spirit-system.com/index.p ... #STABI_TAB
//Latjo


Ok my GYRO was reversed. I have changed that now. When i increase GYRO in the TX the number increases in the Diagnostic tab. When I have the GYRO at 31% in the TX it is -50 in the Diagnostic tab and the Stabilisation says Engaged.


Hi
You have to solve the issue whith channel 5 gyro in tx maybe you have some subtrim or the end points not right -100 100 subtrim 0,and no mixing.Look in tx monitor that channel 5 moves from 0-100%.

Resque activeted depends on that you have a neg value in diagnostic tab gyro channel 5.

https://www.youtube.com/watch?v=BQZoTeE1KP4
https://www.youtube.com/watch?v=fZj7u1r--is
https://www.youtube.com/watch?v=WVRHJSQ ... v_&index=9
Diffrent videos on setting up gyro on a heli whith DX6i.
//Latjo


isent
Author:  Paula [ Thu 24. Dec 2020 15:15:13 ]
Post subject:  Re: Adjusting Gyro Dx6i
Maybe it's my D/R?
I can see in the monitor window on my TX that ch5 doesn't go from 0 to 100% but i can't see why.
Travel adjust is all 100%
Sub trim all at 0%
It's definitely activating rescue/stabi or whatever i've got selected.
Author:  Paula [ Thu 24. Dec 2020 15:58:29 ]
Post subject:  Re: Adjusting Gyro Dx6i
Just realised it's not doing 100% because of my GYRO settings.
That makes sense i guess.
I'll watch the videos now.
Thank you for your help!

Attachments:
IMG_0280.jpeg
IMG_0280.jpeg [ 2.86 MiB | Viewed 191 times ]
Page 1 of 1 All times are UTC + 1 hour
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/