Spirit System
https://www.spirit-system.com/phpBB3/

uSpirit severe tail wag - motorized tail
https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=4352
Page 2 of 5

Author:  daniel_i [ Thu 22. Oct 2020 15:42:20 ]
Post subject:  Re: uSpirit severe tail wag - motorized tail

Many thanks man!

Did I get you right?
Attachment:
7.png
7.png [ 1.18 MiB | Viewed 295 times ]

Author:  fassla [ Thu 22. Oct 2020 15:48:53 ]
Post subject:  Re: uSpirit severe tail wag - motorized tail

correct, you do not need ground for tail signal on any of the available FBL systems (JST2 is sufficient to hold signal cable)
;)

Author:  daniel_i [ Fri 23. Oct 2020 11:32:57 ]
Post subject:  Re: uSpirit severe tail wag - motorized tail

fassla wrote:
I can see you have rudder frequency 50Hz, switch to 333Hz, and delay to 0.


Hi @fassla I didn’t get you with rudder frequency, where is this setup? You actually mean pirouette consistency?


Sent from my iPhone using Tapatalk

Author:  daniel_i [ Fri 23. Oct 2020 11:55:29 ]
Post subject:  Re: uSpirit severe tail wag - motorized tail

Huge thanks @fassla
Managed to get this thing in air. Btw are you in spirit team or ...?

https://youtu.be/04BevZAqBsE

Now of course tail does a bounce back and cyclic has a bit of shaking but I think this should be addressable through the parameters.


Sent from my iPhone using Tapatalk

Author:  fassla [ Fri 23. Oct 2020 13:46:22 ]
Post subject:  Re: uSpirit severe tail wag - motorized tail

happy to see you are up in the air ;-)

and, No I'm not in spirit team

Author:  daniel_i [ Sat 24. Oct 2020 22:32:45 ]
Post subject:  Re: uSpirit severe tail wag - motorized tail

fassla wrote:
happy to see you are up in the air ;-)

and, No I'm not in spirit team


Thanks! tail and cyclic are fine.
I am now trying to figure out why I don`t get the current RPM value through that MTX pin.
I plugged that into P pin of P/E/A port of uSpirit and I get no output.
Also I counted 24 poles in the sunnysky motor => 12 value in sensing divider, right?

Author:  HeliMLM [ Sun 25. Oct 2020 7:15:46 ]
Post subject:  Re: uSpirit severe tail wag - motorized tail

Hi,
did you plug into middle pin? i would say the manual could be misleading in that point...it says: „μSpirit - P pin - pin in the middle of P/E/A port“… but maybe i am wrong… do not know microSpirit.

Author:  fassla [ Sun 25. Oct 2020 9:29:50 ]
Post subject:  Re: uSpirit severe tail wag - motorized tail

I think Tomas needs to have a look on it. Neither P nor E on uSpirit is delivering a RPM value

Author:  daniel_i [ Sun 25. Oct 2020 9:31:24 ]
Post subject:  Re: uSpirit severe tail wag - motorized tail

fassla wrote:
I think Tomas needs to have a look on it.
Okay, but is your setup reading the current RPM?


Sent from my iPhone using Tapatalk

Author:  fassla [ Sun 25. Oct 2020 9:33:02 ]
Post subject:  Re: uSpirit severe tail wag - motorized tail

for some reason I use the OMP ESC on a different FBL system....and there it is working as I showed to you

Page 2 of 5 All times are UTC + 1 hour
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/