It is currently Thu 28. Mar 2024 15:16:04

All times are UTC + 1 hour





Post new topic Reply to topic  [ 44 posts ]  Go to page Previous  1, 2, 3, 4, 5  Next
  Print view Previous topic | Next topic 
Author Message
PostPosted: Thu 22. Oct 2020 15:42:20 
Offline

Joined: Wed 09. Sep 2020 14:20:00
Posts: 28
Many thanks man!

Did I get you right?
Attachment:
7.png
7.png [ 1.18 MiB | Viewed 293 times ]


Top
 Profile  
 
PostPosted: Thu 22. Oct 2020 15:48:53 
Offline

Joined: Sat 20. Jul 2019 21:06:40
Posts: 54
correct, you do not need ground for tail signal on any of the available FBL systems (JST2 is sufficient to hold signal cable)
;)


Top
 Profile  
 
PostPosted: Fri 23. Oct 2020 11:32:57 
Offline

Joined: Wed 09. Sep 2020 14:20:00
Posts: 28
fassla wrote:
I can see you have rudder frequency 50Hz, switch to 333Hz, and delay to 0.


Hi @fassla I didn’t get you with rudder frequency, where is this setup? You actually mean pirouette consistency?


Sent from my iPhone using Tapatalk


Top
 Profile  
 
PostPosted: Fri 23. Oct 2020 11:55:29 
Offline

Joined: Wed 09. Sep 2020 14:20:00
Posts: 28
Huge thanks @fassla
Managed to get this thing in air. Btw are you in spirit team or ...?

https://youtu.be/04BevZAqBsE

Now of course tail does a bounce back and cyclic has a bit of shaking but I think this should be addressable through the parameters.


Sent from my iPhone using Tapatalk


Top
 Profile  
 
PostPosted: Fri 23. Oct 2020 13:46:22 
Offline

Joined: Sat 20. Jul 2019 21:06:40
Posts: 54
happy to see you are up in the air ;-)

and, No I'm not in spirit team


Top
 Profile  
 
PostPosted: Sat 24. Oct 2020 22:32:45 
Offline

Joined: Wed 09. Sep 2020 14:20:00
Posts: 28
fassla wrote:
happy to see you are up in the air ;-)

and, No I'm not in spirit team


Thanks! tail and cyclic are fine.
I am now trying to figure out why I don`t get the current RPM value through that MTX pin.
I plugged that into P pin of P/E/A port of uSpirit and I get no output.
Also I counted 24 poles in the sunnysky motor => 12 value in sensing divider, right?


Top
 Profile  
 
PostPosted: Sun 25. Oct 2020 7:15:46 
Offline
User avatar

Joined: Tue 10. Mar 2020 14:36:22
Posts: 352
Hi,
did you plug into middle pin? i would say the manual could be misleading in that point...it says: „μSpirit - P pin - pin in the middle of P/E/A port“… but maybe i am wrong… do not know microSpirit.

_________________
cheers
Michael


Top
 Profile  
 
PostPosted: Sun 25. Oct 2020 9:29:50 
Offline

Joined: Sat 20. Jul 2019 21:06:40
Posts: 54
I think Tomas needs to have a look on it. Neither P nor E on uSpirit is delivering a RPM value


Last edited by fassla on Sun 25. Oct 2020 9:31:26, edited 1 time in total.

Top
 Profile  
 
PostPosted: Sun 25. Oct 2020 9:31:24 
Offline

Joined: Wed 09. Sep 2020 14:20:00
Posts: 28
fassla wrote:
I think Tomas needs to have a look on it.
Okay, but is your setup reading the current RPM?


Sent from my iPhone using Tapatalk


Top
 Profile  
 
PostPosted: Sun 25. Oct 2020 9:33:02 
Offline

Joined: Sat 20. Jul 2019 21:06:40
Posts: 54
for some reason I use the OMP ESC on a different FBL system....and there it is working as I showed to you


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 44 posts ]  Go to page Previous  1, 2, 3, 4, 5  Next

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .