| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| Graupner Receiver, SUMD, Hott Integration and USB Connection https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=3937 |
Page 1 of 1 |
| Author: | Capelini81 [ Mon 04. May 2020 10:48:26 ] |
| Post subject: | Graupner Receiver, SUMD, Hott Integration and USB Connection |
Hey Folks, i´m a bit confused about my "old" Setup on an old Spirit and an Graupner GR-24. I've connected them via SUMD form Receiver Port 8 to RUD port on Spirit. Everything works fine but now I want to integrate Telemetrie and got here some questions: In the Wiki "Hott integration" you are writing, that I need to connect Spirit SYS Port with the Telemetrie port of the Receiver. For Telemetrie ok, but you are also writing that the SUMD Channel transmission will work over the Telemetrie Port. - Is this correct? So I can or must unplug the Channel transmission cable on the RUD port? Will the UBS interface Work parallel to the Channel transmission on the SYS Port? Otherwise I won't be able to configure Spirit in this case. Ore do I need to connect the Channel transmission from the Receiver separate in this case? Thanks Marcel |
|
| Author: | enied [ Mon 04. May 2020 11:20:24 ] |
| Post subject: | Re: Graupner Receiver, SUMD, Hott Integration and USB Connec |
Hi, 1) connect the ESC to the Spirit Satellite Port #1 (special cable required) 2) connect the Telemerty Port of the GR-24 to the SYS Port (special cable required) This will allow to get telemetry data AND configure the Spirit using your transmitter. To use the USB Cable: disconnect the HoTT integration cable from the SYS Port and plug in the USB cable. Now you can configure the Spirit or Geolink via USB. Do NOT use an Y-adapter on the SYS Port. In no case you have to disconnect the SUMD cable. BR Eugen |
|
| Author: | Capelini81 [ Mon 04. May 2020 11:29:58 ] |
| Post subject: | Re: Graupner Receiver, SUMD, Hott Integration and USB Connec |
enied wrote: Hi, already done with Unisens1) connect the ESC to the Spirit Satellite Port #1 (special cable required) enied wrote: 2) connect the Telemerty Port of the GR-24 to the SYS Port (special cable required) clear so farenied wrote: This will allow to get telemetry data AND configure the Spirit using your transmitter. I will configure Spirit with my Computer and transmit the Channels via SUMD at the SYS Port - This won´t work , correct?To use the USB Cable: disconnect the HoTT integration cable from the SYS Port and plug in the USB cable. Now you can configure the Spirit or Geolink via USB. Do NOT use an Y-adapter on the SYS Port. Ihm clear about the wiring but not where the SUMD Signals will be transmitted enied wrote: BR Eugen KR Marcel |
|
| Author: | enied [ Mon 04. May 2020 11:38:02 ] |
| Post subject: | Re: Graupner Receiver, SUMD, Hott Integration and USB Connec |
The SUMD cable needs to be connected from GR-24 channel 8 to the Spirit RUD Port. It never needs to be disconnected. BR Eugen |
|
| Author: | Capelini81 [ Mon 04. May 2020 12:22:56 ] |
| Post subject: | Re: Graupner Receiver, SUMD, Hott Integration and USB Connec |
enied wrote: The SUMD cable needs to be connected from GR-24 channel 8 to the Spirit RUD Port. It never needs to be disconnected. BR Eugen Thanks, I read the Wiki wrong... KR Marcel |
|
| Page 1 of 1 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|