It is currently Mon 14. Oct 2024 10:35:36

All times are UTC + 1 hour





Post new topic Reply to topic  [ 6 posts ] 
  Print view Previous topic | Next topic 
Author Message
PostPosted: Thu 21. Mar 2024 1:44:53 
Offline

Joined: Mon 11. Feb 2019 2:33:45
Posts: 3
hello. im wondering how and what setting do i use for a direct drive helicopter? what do i put in for gear ratio, and what do I use for sensing divider. i dont know how many poles the goo-sky rs4 venom motor has. this is my first time setting up the governor in the spirit.


Top
 Profile  
 
PostPosted: Thu 21. Mar 2024 17:17:10 
Offline

Joined: Sat 29. Apr 2023 21:36:44
Posts: 30
Location: CH
Hi
oldbetsy wrote:
what do i put in for gear ratio, a

No gear -> no ratio -> 1
oldbetsy wrote:
i dont know how many poles the goo-sky rs4 venom motor has. this is my first time setting up the governor in the spirit.

Ask the Goosky support.

_________________
Have a good time
Thomas


Top
 Profile  
 
PostPosted: Fri 22. Mar 2024 10:57:04 
Offline

Joined: Wed 15. Apr 2020 11:16:36
Posts: 8
Hello,

Try this.
WITHOUT BLADES
You open the Governor/Throttle settings window.
You disable the Governor (on the top right on the window), you enter a sensing divider (2, 3, 4 ...), then you see the rpm returned il the RPM sensor window (Current rpm).
If this is in correlation with the kV and the LiPo cells, then you have the number of poles (sensing divider X2).
BUT you don't care about the number of poles because you juste want to have the correct rpm returned ...

If the rpm returned are too low, then you decrease the sensing divider.
If it's too high, then you increase the sensing divider.

Normally you should know roughly the rpm of your helicopter ...

When you have the correct sensing divider, then you enable the Governor on the top right on the window.

Hervé


Top
 Profile  
 
PostPosted: Sat 23. Mar 2024 1:19:46 
Offline

Joined: Mon 11. Feb 2019 2:33:45
Posts: 3
thank you for the inputs. i will try your suggestions


Top
 Profile  
 
PostPosted: Wed 27. Mar 2024 19:09:09 
Offline

Joined: Mon 11. Feb 2019 2:33:45
Posts: 3
well that worked like a charm. I set the ratio to 1 and keep increasing or decreasing the divider until the actual head speed matched what the spirit was saying. got the head speed with my tacometer and adjusted the divider. and it was right at 20 for the divider


Top
 Profile  
 
PostPosted: Thu 28. Mar 2024 2:12:59 
Offline

Joined: Sat 13. May 2023 5:41:05
Posts: 11
If you don't have a tach you can use Spirit's vibration Spectrum Analyser to find the vibration level of the main rotor, which will tell you the actual RPMs, then adjust.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .