It is currently Mon 14. Oct 2024 8:34:00

All times are UTC + 1 hour





Post new topic Reply to topic  [ 4 posts ] 
  Print view Previous topic | Next topic 
Author Message
PostPosted: Sun 15. Sep 2024 14:46:29 
Offline

Joined: Wed 14. Aug 2024 14:59:22
Posts: 5
I bought an SAB RAW 500 second hand (without FBL) with MKS HV9767 cyclic servos and an MKS HV9780 tail servo. I now installed a Spirit GT and wired everything up as in the attached file. My receiver is an FrSky R-XSR that I flashed with F.port firmware. I have a Radiomaster TX16S II Max transmitter in which I created a blank model and only configured and bound the FrSky R-XSR receiver (FrSkyX2 mode, LBT(EU) protocol).
When I connect the battery (LiPo 6s 4000 mAh), the tail servo occasionally makes a slight noise (the cyclic servos only initialize and then remain quiet). Then when I turn on my transmitter, the tail servo starts jittering like crazy. When setting up the FBL via the wizard, I entered the correct frequency values ​​for the tail servo (760µs/560Hz) and the cyclic servos (1520µs/333Hz) and I chose FrSky F.Port as the protocol. Does anyone have an idea of what could be the issue? I hope the tail servo is not toast :-(


Attachments:
Spirit GT wiring2.pdf [244.22 KiB]
Downloaded 9 times


Last edited by Helihello on Mon 16. Sep 2024 17:47:51, edited 1 time in total.
Top
 Profile  
 
PostPosted: Sun 15. Sep 2024 18:10:29 
Offline

Joined: Wed 21. Dec 2016 15:13:38
Posts: 556
Location: Germany
Hello,
The switching on sequence is wrong, the remote control is always switched on first and only then the helicopter and not the other way around, this is a fundamental error in operation!

Regards


Top
 Profile  
 
PostPosted: Sun 15. Sep 2024 19:27:17 
Offline

Joined: Wed 14. Aug 2024 14:59:22
Posts: 5
Mattes61 wrote:
Hello,
The switching on sequence is wrong, the remote control is always switched on first and only then the helicopter and not the other way around, this is a fundamental error in operation!

Regards


Yes, you're totally right, that's also how I did it apart from the first time when binding. So, indeed, when I connect the battery with my radio transmitter on and the RAW 500 model selected, the tail servo first makes some slight noises and then starts jittering :?


Top
 Profile  
 
PostPosted: Mon 16. Sep 2024 17:33:50 
Offline

Joined: Wed 14. Aug 2024 14:59:22
Posts: 5
I came across this thread and I knew that only the green LED was lit on my FrSky R-XSR receiver when it is bound to my radio. So I realised I had accidentally put the receiver in CPPM mode during the binding process :roll: . FPort obviously needs SBUS mode so I've now put the receiver in SBUS mode (green and blue LED on when bound) and the jitter on my tail servo is gone, hourray :) !!!

Now I noticed that, from time to time, my radio loses telemetry as described here, so I might downgrade the F.port firmware on the receiver from 2.1.1 to 2.1.0 and see whether that solves that issue.

As indicated in my first post, the tail servo makes occasionally a crackling noise (a bit similar to a Geiger counter with low radiation levels). Is this normal or does it mean the servo is EOL ?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .