It is currently Sun 10. Nov 2024 20:44:03

View unanswered posts | View active topics


Board index » English » HELI » Support

All times are UTC + 1 hour





Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 
  Print view Previous topic | Next topic 
Author Message
doingmainestuff
PostPosted: Fri 15. Dec 2023 2:33:30 
Offline

Joined: Tue 03. Oct 2023 21:39:39
Posts: 37
I built a scale heli, and I'm using the Spirit GT.

How can I free up a channel for my electric retracts? I bought a Spektrum AR6610T, which is bound and working. But, for my life, I cannot figure out how to free up a channel for the gear.

The Gyro is using the gear channel by default. The BING/PROG port on the AR6610T is connected to the RUD/ELE on the GT. So, I have five free channels on the AR6610T I was hoping to use for the gear.

Tips? Tricks?


Attachments:
File comment: I have my AR6610T wired precisely like this.
1200px-Ar6610t-wiring.jpg
1200px-Ar6610t-wiring.jpg [ 172.71 KiB | Viewed 594 times ]
Top
 Profile  
 
senaka
PostPosted: Fri 15. Dec 2023 8:51:40 
Offline

Joined: Wed 10. May 2023 9:36:53
Posts: 37
Location: The Netherlands
You may need to re assign the switch you like to use for the retracts to another free channel. This should be done on the transmitter this is how I do it on FrSKY ethos transmitter.
Top
 Profile  
 
Mattes61
PostPosted: Fri 15. Dec 2023 8:54:41 
Offline

Joined: Wed 21. Dec 2016 15:13:38
Posts: 566
Location: Germany
Hello,
one trick you can do is to deactivate the gyro-Channel in Spirit Settings and make your settings directly in the FBL -
second trick is to use under special functions an dedicated output to switch your gear - I am not shure there are two possible channels which can be taken, please look in the list...

Attachment:
Info_001.jpg
Info_001.jpg [ 39.69 KiB | Viewed 578 times ]


Top
 Profile  
 
ZeXx86
PostPosted: Fri 15. Dec 2023 8:55:21 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12436
Assign F: Output to AUX2 in the channels window and select a free channel there. You can use for example channel 10. Then connect landing gear to AUX2 port.

_________________
Spirit System developer
Top
 Profile  
 
doingmainestuff
PostPosted: Fri 15. Dec 2023 13:56:09 
Offline

Joined: Tue 03. Oct 2023 21:39:39
Posts: 37
ZeXx86 wrote:
Assign F: Output to AUX2 in the channels window and select a free channel there. You can use for example channel 10. Then connect landing gear to AUX2 port.


Can I do this even with the BEC cable plugged in to AUX2?
Top
 Profile  
 
ZeXx86
PostPosted: Fri 15. Dec 2023 14:01:53 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12436
Yes, or you can use CH0 port as well.

_________________
Spirit System developer
Top
 Profile  
 
doingmainestuff
PostPosted: Fri 15. Dec 2023 15:06:57 
Offline

Joined: Tue 03. Oct 2023 21:39:39
Posts: 37
ZeXx86 wrote:
Yes, or you can use CH0 port as well.


I tried CH0 and mapped it in "Channels." But, it won't toggle. It simply says (State 1) and on. What am I doing wrong?
Top
 Profile  
 
toni67
PostPosted: Fri 15. Dec 2023 15:13:18 
Offline

Joined: Sat 29. Apr 2023 21:36:44
Posts: 30
Location: CH
doingmainestuff wrote:
ZeXx86 wrote:
Yes, or you can use CH0 port as well.


I tried CH0 and mapped it in "Channels." But, it won't toggle. It simply says (State 1) and on. What am I doing wrong?


ZeXx86 meant: BEC to CH0... ;)

_________________
Have a good time
Thomas
Top
 Profile  
 
ZeXx86
PostPosted: Fri 15. Dec 2023 15:17:34 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12436
I meant F: Output to CH0 instead of Output to AUX2 if it is unused.
But both should work, also BEC at CH0.

There is nothing else needed. It should work immediately with a servo.
You can also assign Throttle function to Channel 1. This should do the trick.

_________________
Spirit System developer
Top
 Profile  
 
doingmainestuff
PostPosted: Sat 16. Dec 2023 13:51:10 
Offline

Joined: Tue 03. Oct 2023 21:39:39
Posts: 37
ZeXx86 wrote:
I meant F: Output to CH0 instead of Output to AUX2 if it is unused.
But both should work, also BEC at CH0.

There is nothing else needed. It should work immediately with a servo.
You can also assign Throttle function to Channel 1. This should do the trick.


When I set Output to AUX2, I don't see the usual "Value 0/1"; I see "State: On (1)." In this mode, the value doesn't toggle like other channels.

I got the gear to work by disabling and using the Gyro channel instead. But I'd like to learn the way you suggested, too.

What have I done wrong?


Attachments:
IMG_0171.jpg
IMG_0171.jpg [ 1.71 MiB | Viewed 539 times ]
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 

Board index » English » HELI » Support

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 6 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .