It is currently Wed 09. Oct 2024 1:38:59

All times are UTC + 1 hour





Post new topic Reply to topic  [ 3 posts ] 
  Print view Previous topic | Next topic 
Author Message
PostPosted: Mon 01. May 2017 20:30:56 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12396
Version 2.4.0 was released!

It brings many new features and improvements:
  • Support for μSpirit unit:
    • Full support of the micro Spirit.
    • Compatible with all peripherals.
    • Can be used on helicopters of 130 - 250 size.
    • Support for ESC/Motor driven rudder.
    • New parameter Rudder - Control type to allow selection of the rudder drive.
    • NOTE: Will be supported by Spirit Aero firmware.
    • IMPORTANT: Older firmwares are not supported!
  • Graupner HoTT integration:
    • ESC Telemetry support.
    • USB interface can be connected without repowering the unit - once integration cable is plugged off, the status led will be turned off and you can plug in the USB interface.
    • Small speed optimization of the integration.
    • Support for μSpirit.
  • OpenTX Integration:
    • ESC Telemetry support.
    • Significantly faster telemetry data refresh rate.
    • USB interface can be connected without repowering the unit - once integration cable is plugged off, the status led will be turned off and you can plug in the USB interface.
    • Support for μSpirit.
  • JETI Duplex Integration:
    • ESC Telemetry support.
    • Telemetry data rate was optimized.
    • Support for Servo reverse CH0 for CCPM 90 swashplate.
    • Support for Subtrim CH0 for CCPM 90 swashplate.
    • Support for μSpirit.
  • In-Flight Vibration Analysis:
    • FIX: Can be used with F: Stabi function.
    • Can be activated all the time with no downside effect.
  • ESC Telemetry:
    • Support for telemetry data from the ESC - all data can be displayed directly in your radio.
    • Available for JETI Duplex, FrSky/OpenTX, Graupner HoTT.
    • New Telem CC, Telem UNI and Telem KONTRONIK telemetry cables.
    • Castle Creations Phoenix and Edge:
      • Battery Voltage
      • Battery Current (experimental)
      • BEC Voltage
      • Consumed Capacity (experimental)
      • ESC Temperature
    • HobbyWing Platinum V4:
      • Battery Voltage
      • Battery Current (experimental)
      • Consumed Capacity (experimental)
      • ESC Temperature
    • Scorpion Tribunus:
      • Battery Voltage
      • Battery Current
      • BEC Voltage
      • Consumed Capacity
      • ESC Temperature
    • Kontronik Kosmik and Jive Pro:
      • Battery Voltage
      • Battery Current
      • BEC Voltage
      • Consumed Capacity
      • ESC Temperature
    • NOTE: All telemetry guides are available at the Wiki pages.
  • Wifi-Link module:
    • Support for the latest 2.4 firmware.
    • Support for the ESC Telemetry.
    • Support for the μSpirit.
    • Improved detection of the firmware version with more clear messages.
  • Spirit Settings - Android:
    • Support for the latest 2.4 firmware.
    • Support for the ESC Telemetry.
    • Support for the μSpirit.
  • Spirit Settings - FreeBSD:
    • Launch scripts for better architecture detection updated.
    • Stability was enhanced.
  • Improved Setup Wizard:
    • New schemes with μSpirit.
    • Improved detection of the unit swapping..
    • New Profiles: T-Rex 150, T-Rex 250, Oxy 2, Blade 130S, Blade 180CFX, Blade 230S.
  • Governor:
    • Sensor Activity analyser was improved to work with all governor sensors.

Update for the Spirit unit, Wifi-Link and Jeti Integration is available in our Download section.

You do not have to change any settings after the update from the previous version 2.3.

Image

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Mon 22. May 2017 9:55:23 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12396
Version 2.4.1 was released!

  • Graupner HoTT integration:
    • Telemetry connection is active also when the telemetry cable is disconnected - feature introduced in 2.4.0 was replaced.
    • USB interface can be connected once you will select the USB connection in the Expert menu (integration).
    • Speed optimization was reverted to increase compatibility.
  • ESC Telemetry:
    • Added support for the RPM readout from all supported ESCs - when no RPM sensor is connected, readout is taken from the ESC.
    • Added support for the Kontronik Jive ESC.
    • Kontronik Jive parameters:
      • Battery Voltage
      • Battery Current
      • BEC Voltage
      • Consumed Capacity
      • ESC Temperature
      • RPM
    • Added Imotor Shunt parameter - correction factor of the Current/Capacity.
    • Castle Creations Talon:
      • Temperature measurement was fixed.
    • HobbyWing Platinum V4:
      • Battery Current and Capacity measurement precision corrected for all models.
      • Big thanks to HobbyWing, Adrian, TomasN and our pilots!
    • NOTE: All telemetry guides are available at the Wiki pages.

  • Rudder stopping performance:
    • Stopping was enhanced to make it more equal when torque is too assymetric.
  • Stabilisation mode:
    • Stabilisation algorithm was slightly enhanced to make it more stable when Direction Control Rate - 0 is configured.
  • Wifi-Link and Jeti integration:
    • Support for the latest firmware 2.4.1 - update available for download.

You do not have to change any settings after the update from the previous version 2.3 and 2.4.0.

Update for the Spirit unit, Wifi-Link and Jeti Integration is available in our Download section.

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Thu 06. Jul 2017 10:14:21 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12396
Version 2.4.2 was released!

  • Graupner HoTT integration:
    • Added new Telemetry variable - Throttle PWM [ms] - reported under Climb rate.
  • OpenTX integration:
    • New diagnostic script for displaying channel values - script diagnostic.lua.
    • Full support for the Log Viewer - script logviewer.lua.
    • Added configuration for the ESC Telemetry.
    • Added new Telemetry variable - Throttle PWM [µs]
  • Jeti integration:
    • RPM readout can't overflow - the max. value is 8191.
  • ESC Telemetry:
    • Castle Creations:
      • Telemetry readout is stable also when Spirit Governor is enabled.
      • Fixed capacity calculation when Spirit Governor is enabled.
    • Kontronik Kosmik & Jive Pro:
      • RPM: readout is compatible with all configurations now.
    • HobbyWing Platinum V4:
      • HobbyWing v4 120A: temperature calculation was corrected.
    • NOTE: All telemetry guides are available at the Wiki pages.
  • Manual:
    • New Chinese traslation was added! (Big Thanks to Mr. Wong)
    • Pin layout for Spirit and µSpirit units is available.
  • Spirit Settings:
    • Real-Time tuning:
      • When special function is assigned but channel is unassigned, the function will be automatically unassigned when window is closed.
    • Translation:
      • New Chinese traslation was added! (Big Thanks to Mr. Wong)
    • Setup Wizard:
      • Updated profiles for T-Rex 150, T-Rex 250, Blade 130S, Blade 230S, Oxy 2 and Oxy 3.
    • News noticement:
      • Automatic noticement of a new available updates.

You do not have to change any settings after the update from the previous version 2.3 and 2.4.x.

Update for the Spirit units and OpenTX Integration is available in our Download section.

_________________
Spirit System developer


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .