It is currently Thu 28. Mar 2024 19:26:42

All times are UTC + 1 hour





Post new topic Reply to topic  [ 9 posts ] 
  Print view Previous topic | Next topic 
Author Message
 Post subject: T-REX 500 tail panning
PostPosted: Sun 21. Feb 2021 22:09:12 
Offline

Joined: Thu 16. Apr 2020 21:18:13
Posts: 8
Hi,

I have a very annoying problem with my T-Rex 500 pro DFC and Spirit II
Originally I flew with the original Align ESC in "non-governor" mode, meaning with a throttle curve. Sorry, I don't know the exact term in English.
This worked well so far, except from some speed drops.

I then bought a Hobbywing Platinum V4 80A ESC, which should allow me to fly in governor mode.

My current problem is that the tail is panning to the right while I am pitching, even with smooth pitch inputs. It usually wipes back to the original position, once I release the pitch.
I followed the tuning guide http://manual.spirit-system.com/index.p ... ning_Guide, but there was no improvement at all. The only thing that mitigated the issue at least a little was playing with the multiplier of the sensor gain until the tail became unstable.

- My tail servo is a Align DS535M
- I basically followed the wizard for my Align 500
- I use the latest firmware on my Spirit II
- I have experimented with the setting from the tuning guide
- My headspeed is around 1850 rpm
- My Spirit II settings are attached

My questions:
- Whenever I change a parameter in the Jeti setting for the Spirit II, will this be effective immediately without saving or disconnecting the battery?
- Is there anything else I could try to stabilize the tail while pitching?

Many thanks for your support in advance

Best regards,
Daniel


Attachments:
TREX500DFCPRO_Hobbywing_0.4ds [255 Bytes]
Downloaded 48 times
Top
 Profile  
 
PostPosted: Thu 04. Mar 2021 14:42:19 
Offline
Site Admin

Joined: Mon 29. Apr 2013 16:06:44
Posts: 12212
Hello,

the problem you have could be caused by too low Advanced/Pirouette Consistency value. I recommend to increase it to 165 at least, but you can try also 170.

Then you can decrease Rudder Delay to value 2-4. This will also help.

After these settings, please increase Gyro Gain as high as possible, until you will observe any oscillations in fast forward flight or more demanding maneuvers.

_________________
Spirit System developer


Top
 Profile  
 
PostPosted: Fri 12. Mar 2021 17:58:47 
Offline

Joined: Thu 05. Oct 2017 20:06:35
Posts: 305
Did this work for you? I have the 500x with the same issue.

It's currently a 're-kit', so I can't try this fix...


Top
 Profile  
 
PostPosted: Fri 12. Mar 2021 18:45:12 
Offline

Joined: Thu 16. Apr 2020 21:18:13
Posts: 8
Sorry guys for not replying earlier. I did not fly the last two, three weeks.

Basically I had to increase the head speed from 1850rpm to around 2250rpm. Apparently the T-REX does not like a too decent headspeed.
In addition to ZeXx86 recommendation I was playing with the Revo Mix, even though when not really recommended.

My tail is now pretty stable - not 100% - but for me it is "good enough" as I do not perform hard flying maneuvers.

Cheers,
Daniel


Top
 Profile  
 
PostPosted: Wed 17. Mar 2021 19:42:12 
Offline

Joined: Thu 05. Oct 2017 20:06:35
Posts: 305
murx wrote:
Sorry guys for not replying earlier. I did not fly the last two, three weeks.

Basically I had to increase the head speed from 1850rpm to around 2250rpm. Apparently the T-REX does not like a too decent headspeed.
In addition to ZeXx86 recommendation I was playing with the Revo Mix, even though when not really recommended.

My tail is now pretty stable - not 100% - but for me it is "good enough" as I do not perform hard flying maneuvers.

Cheers,
Daniel


Are you able to post your final settings, please?


Top
 Profile  
 
PostPosted: Thu 18. Mar 2021 9:10:46 
Offline

Joined: Thu 16. Apr 2020 21:18:13
Posts: 8
Yes, I can do the next days


Top
 Profile  
 
PostPosted: Fri 19. Mar 2021 19:26:09 
Offline

Joined: Thu 16. Apr 2020 21:18:13
Posts: 8
Here you are....
It's just my idle1 profile. I do not really fly 3D.


Attachments:
3.2.2_1.0.3_20210319_0.4ds [255 Bytes]
Downloaded 56 times
Top
 Profile  
 
PostPosted: Fri 19. Mar 2021 19:50:51 
Offline

Joined: Thu 05. Oct 2017 20:06:35
Posts: 305
Thanks.

I cant look at it in the 4ds viewer, so i'll upload it on a spirit later.

http://4dsviewer.spirit-system.com/
"Unsupported version: heli-3.2.2"


Top
 Profile  
 
PostPosted: Fri 19. Mar 2021 19:54:28 
Offline
User avatar

Joined: Sun 09. Jun 2013 13:14:17
Posts: 962
Location: Plzeň
Open it in demo mode Spirit settings SW 3.2.2
-

jjuk wrote:
Thanks.

I cant look at it in the 4ds viewer, so i'll upload it on a spirit later.

http://4dsviewer.spirit-system.com/
"Unsupported version: heli-3.2.2"

_________________
Spirit System (Spirit W1, RS & GTR & all the others)
Spirit Wave & JETI DS 12
http://www.habada.cz


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .