Spirit System
https://www.spirit-system.com/phpBB3/

Questions about F3C Setup (Spirit 2)
https://www.spirit-system.com/phpBB3/viewtopic.php?f=17&t=4244
Page 2 of 5

Author:  heliflieger8587 [ Sun 13. Sep 2020 14:33:54 ]
Post subject:  Re: Questions about F3C Setup (Spirit 2)

Here my settings for the Goblin 700.

Attachments:
kunstflug.4ds [255 Bytes]
Downloaded 75 times

Author:  ZeXx86 [ Sun 13. Sep 2020 17:24:58 ]
Post subject:  Re: Questions about F3C Setup (Spirit 2)

Thank you very much for the video.

If time will allow tomorrow we can prepare special firmware for you. It will be interesting to see if it will help.
So we can make it perfect for F3C. Then it can be embedded in official firmware later.

Author:  eric38 [ Mon 14. Sep 2020 9:07:13 ]
Post subject:  Re: Questions about F3C Setup (Spirit 2)

Hello,
I'm new Spirit RS user, i tried and settings yesterday afternoon on my Urukay, i remembered your problem and i tried but no problem, the model stay strictkly vertically without correction.
Eric

Author:  heliflieger8587 [ Mon 14. Sep 2020 9:30:41 ]
Post subject:  Re: Questions about F3C Setup (Spirit 2)

Hello Eric,

it depends on how hard you fly the curve. If you make a big bow, the problem does not occur, or only minimally. If you fly quickly with a small radius, this effect occurs.

When the candle goes out this is e.g. not disturbing, because you have to take your nose down anyway to pick up speed again.

greetings Björn

Author:  fri09 [ Wed 16. Sep 2020 18:52:04 ]
Post subject:  Re: Questions about F3C Setup (Spirit 2)

Hello,

I definitely don't want to stress! I'm just curious if you will provide the special firmware before weekend?
The weather will be great and it would be a great chance to test it...

Frieder

Author:  ZeXx86 [ Thu 17. Sep 2020 7:46:20 ]
Post subject:  Re: Questions about F3C Setup (Spirit 2)

Hello,

here it is:
http://spirit-system.com/dl/fw//spirit-fw-3.1.32.4df

No need to change anything in the settings.

Author:  heliflieger8587 [ Fri 18. Sep 2020 10:41:18 ]
Post subject:  Re: Questions about F3C Setup (Spirit 2)

Hi,

I am currently on the flight field and test your new version.
I must unfortunately say, that the effekt is also present with this version.
I think not so hard, but with a higher rpm my goblin flip about 15°

Have you any ideas, what we can do next?

Bjoern

Author:  tomsl [ Sat 19. Sep 2020 2:43:05 ]
Post subject:  Re: Questions about F3C Setup (Spirit 2)

Hello
I can confirm this problem
I was flying today and I have the same behavior 15°


Thomas

Author:  fri09 [ Sat 19. Sep 2020 8:20:39 ]
Post subject:  Re: Questions about F3C Setup (Spirit 2)

Hi,

here is what I experienced with the special firmware:
The first candle I flew had the same effect like before. The following candles the tilt became less until it was nearly gone.
But the firmware also caused other unwanted behavior. First of all it feels less stable while cruising and in straight passages. When I steer pitch while flying forwards the heli does an additional nick-movement, so that it flies in shape of a wave.

Beside the "candle-problem", I also still have a bouncing after cyclic input, regardless of the new firmware. Setting the Elevator Filter to 4 helped a lot. So I wonder if it would be possible to increase that damping-effect (like a value of 5)?

Great thanks for your effort!

Frieder

Author:  ZeXx86 [ Sat 19. Sep 2020 10:06:18 ]
Post subject:  Re: Questions about F3C Setup (Spirit 2)

Hi,

in that case the problem seem to be something else.

Can you verify what will be result when Flight Style is set to 1?

Page 2 of 5 All times are UTC + 1 hour
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/