| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| New RTH State (4) https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=4017 |
Page 2 of 2 |
| Author: | yufasa [ Sat 30. May 2020 17:42:03 ] |
| Post subject: | Re: New RTH State (4) |
Awesome! Cannot wait to get out tomorrow...Wife's birthday today so no flying for me:) |
|
| Author: | jjuk [ Sat 30. May 2020 21:22:50 ] |
| Post subject: | Re: New RTH State (4) |
When you engage RTH, does the heli react at once? Mine continues in the direction it was travelling for 1-2 seconds before starting to return. It doesn't climb either so if it was falling when RTH is engaged I'm sure it would crash. |
|
| Author: | Fortune7 [ Sat 30. May 2020 22:35:55 ] |
| Post subject: | Re: New RTH State (4) |
jjuk wrote: When you engage RTH, does the heli react at once? Mine continues in the direction it was travelling for 1-2 seconds before starting to return. It doesn't climb either so if it was falling when RTH is engaged I'm sure it would crash. Yes, instantly for me. It only takes-over cyclic pitch so you still have to work collective. I think you can add-in min and max height with RTH but I haven't tried that yet. To be clear, I'm only operating RTH for this, Rescue is separate. Just to add I had to do compass calibration again after swapping the Geolink between models - I checked the 'heading' figure for north orientation on the Geolink settings first page and it was 78, not 90 +/- 4 as specified. Went through calibration again (it does take a while to capture all orientations) and it reported 90. You need a solid blue LED before liftoff on the Geolink. I was impressed how accurate the RTH is, and once there, it's rock solid except for height control. Cheers, Andy |
|
| Author: | horneteer [ Sun 31. May 2020 8:32:10 ] |
| Post subject: | Re: New RTH State (4) |
I think you can assign altitude hold to the same channel. |
|
| Author: | tabbie [ Mon 01. Jun 2020 10:08:28 ] |
| Post subject: | Re: New RTH State (4) |
I have updated my T-Rex to 3.1 and Geo link accordingly. When I go to RTH tab and set my transmitter to 50% switch I find a response (3) and not (4) for the RTH position update. What ist (3) meaning and why I will not get (4)? I have checked the manual for Geo Link but there is still (1) for RTH and (2) for home position. |
|
| Author: | buttles [ Mon 01. Jun 2020 10:50:59 ] |
| Post subject: | Re: New RTH State (4) |
tabbie wrote: I have updated my T-Rex to 3.1 and Geo link accordingly. When I go to RTH tab and set my transmitter to 50% switch I find a response (3) and not (4) for the RTH position update. What ist (3) meaning and why I will not get (4)? I have checked the manual for Geo Link but there is still (1) for RTH and (2) for home position. You may need to play with endpoints a bit. It might not be exactly 50% in your Tx to get 4 to trigger |
|
| Author: | ZeXx86 [ Mon 01. Jun 2020 13:01:12 ] |
| Post subject: | Re: New RTH State (4) |
Please try to set -50% in your radio, very likely your channel is just reversed. |
|
| Page 2 of 2 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|