It is currently Thu 28. Mar 2024 19:12:01

All times are UTC + 1 hour





Post new topic Reply to topic  [ 4 posts ] 
  Print view Previous topic | Next topic 
Author Message
PostPosted: Sun 24. May 2020 13:54:36 
Offline

Joined: Fri 22. May 2020 23:18:27
Posts: 18
Hi,

I'm using Spektrum iX12 transmitter and Spektrum AR637T receiver connected to Spirit Pro in PWM mode. All cables are connected upon instructions, so I use Jeti cable for AIL/PIT/ELE + 2 cables for RUD and AUX1.

In Spirit settings I have chosen 120° swash plate and PWM mode. When I move the sticks in iX12 all indicators in Diagnostic TabPage are moving right, but the real swashplate on the helicopter is moving not right. If I move the elevator stick, the whole swashplate moves up/down (acts like collective). If I move the collective stick on iX12, the swashplate tilts forward or backward (acts like elevator).

What do I bad?

Thanx!


Attachments:
20200523_003854.jpg
20200523_003854.jpg [ 1.54 MiB | Viewed 239 times ]


Last edited by MaxSupercars on Sun 24. May 2020 18:45:06, edited 1 time in total.
Top
 Profile  
 
PostPosted: Sun 24. May 2020 14:31:01 
Offline

Joined: Tue 05. May 2020 21:20:58
Posts: 110
There is a whole setup you need to go through. When you run the wizard you:
1) set up you connection - in your case PWM, the orientation of your spirit and the swash
2) configure the travel and direction of your stick - this is also the “Diagnostic” page when not in wizard mode
3) set up your servo direction - here is is more important to configure the movement of the swash and tail when moving the heli before you touch the control sticks! Once you have the directions fixed by selecting the appropriate check boxes for each servo and/or the pitch you can now go into your radio and reverse the direction of the servo output if the sticks are still moving the swash in the wrong direction.
4) set 0 pitch/ set limits/max travel/6 degree reference etc.
5) setup up any bank defaults you would like and you are done....


I am making a video of this but I am waiting on the re-release of 3.0 before it will be out.

Keep asking away as there are people here that will help


Top
 Profile  
 
PostPosted: Sun 24. May 2020 18:12:22 
Offline

Joined: Tue 17. Mar 2015 3:10:20
Posts: 113
You have at least one servo where the direction needs to be reversed. See "Servo Reverse" on the "Servos" screen. Check reverse for the servo(s) that are moving in the wrong direction. If you follow the Wizard exactly you will have success, that is, you should read everything.


Top
 Profile  
 
PostPosted: Sun 24. May 2020 18:21:09 
Offline

Joined: Fri 22. May 2020 23:18:27
Posts: 18
Guys, thanx for help. You were right.
I reversed 2 servos for front CH1 and CH3 and now it works properly!

Thank you!

Max


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  



Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
skymiles_red v1.0.1 designed by Team -Programming forum-سيارات للبيع .