| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| [SOLVED] srxl2 AR6610T https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=3791 |
Page 10 of 12 |
| Author: | Neilsteers [ Fri 29. May 2020 12:13:30 ] |
| Post subject: | Re: srxl2 AR6610T |
Any news on this release Tomas ? Thanks |
|
| Author: | MaxSupercars [ Fri 29. May 2020 13:38:45 ] |
| Post subject: | Re: srxl2 AR6610T |
Is already out since yesterday or so. Check the download page for v3.1.0 here: http://spirit-system.com/download.php |
|
| Author: | Neilsteers [ Fri 29. May 2020 16:20:59 ] | ||
| Post subject: | Re: srxl2 AR6610T | ||
This is how I have to set up to get the stick inputs to respond although aileron does not show reversal in spirit software but does work on the Heli, On spirit, is this ok ? Red in sys Esc in aux1 Brown/red to rud and orange to pit On ar6610 Jeti cable to port 1 Aile to port 2 Ele port 3 Pitch to port6 Ar6610 latest firmware and spirit and setup software up to date
|
|||
| Author: | Neilsteers [ Fri 29. May 2020 16:40:20 ] |
| Post subject: | Re: srxl2 AR6610T |
Well got to the servo trim setup page and the spirits blue light goes out, go back to diagnostics and it comes back on so obviously that approach does not work |
|
| Author: | 10x [ Fri 29. May 2020 16:56:02 ] |
| Post subject: | Re: srxl2 AR6610T |
Why have you got your servo's plugged into the receiver? They should be plugged into the Spirit.... |
|
| Author: | Neilsteers [ Fri 29. May 2020 17:56:43 ] |
| Post subject: | Re: srxl2 AR6610T |
Nothing happens they don’t respond to stick movements on the servos or in the wizard |
|
| Author: | 10x [ Fri 29. May 2020 18:18:08 ] |
| Post subject: | Re: srxl2 AR6610T |
1st,make sure you have updated 6610t to latest FW, then in spirit/ wizzard make sure you have receiver set to SRXL2 then follow the wizzard instructions and all will be ok... |
|
| Author: | Neilsteers [ Sat 30. May 2020 19:33:15 ] |
| Post subject: | Re: srxl2 AR6610T |
Finally sorted and ready to maiden, one question where should I plug the single yellow Rpm signal wire from the hw platinum esc Into in the spirit ? I have the term uni cable from the esc into sat1 on the spirit and geolink into sat 2 |
|
| Author: | MaxSupercars [ Sat 30. May 2020 20:02:22 ] |
| Post subject: | Re: srxl2 AR6610T |
So finally installed the 3.1.0 Firmware into Spirit Pro. Spektrum AR637T receiver works now with Spirit Pro in SRXL2 mode!!! I had to put the Jeti Integration cable into Channel 1 (Throttle) on receiver and re-route the Throttle output to other free channel (CH5 - Gear in my case). I control my ESC direct from receiver. Few tests with Jeti cable on AR637T side: - Bind/Prg/SRXL2 - port works NOT !!! - CH1 (Throttle) works in SRXL2 - small 4pin JST SRXL2 on top of AR637T works the same way too in SRXL2 |
|
| Author: | yufasa [ Sat 30. May 2020 20:07:34 ] |
| Post subject: | Re: srxl2 AR6610T |
@Neilsteers the RPM, yellow wire, goes to the middle pin on the elevator/Pitch/Aileron connector |
|
| Page 10 of 12 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|