now it works
I first connected the cable to channel one.
Then I connected it to the bind channel.
Thanks to for help!
| Spirit System https://www.spirit-system.com/phpBB3/ |
|
| [SOLVED] srxl2 AR6610T https://www.spirit-system.com/phpBB3/viewtopic.php?f=20&t=3791 |
Page 7 of 12 |
| Author: | 10x [ Thu 23. Apr 2020 21:07:10 ] |
| Post subject: | Re: srxl2 AR6610T |
Are you powering up the receiver with a battery? when connected to the PC. |
|
| Author: | HeliMLM [ Thu 23. Apr 2020 21:28:48 ] |
| Post subject: | Re: srxl2 AR6610T |
... and is Spektrum Programmer App logged into your Spektrum account? (left, upper) there should be written "Logged in as" & your Spektrum account (first) name... |
|
| Author: | Joker [ Thu 23. Apr 2020 21:31:00 ] |
| Post subject: | Re: srxl2 AR6610T |
i have tryed with and without a battary. without a battery i have put the check "power cabel" an the receiver is slowly blinking. |
|
| Author: | Joker [ Thu 23. Apr 2020 21:41:20 ] |
| Post subject: | Re: srxl2 AR6610T |
now it works I first connected the cable to channel one. Then I connected it to the bind channel. Thanks to for help!
|
|
| Author: | 10x [ Thu 23. Apr 2020 21:47:45 ] |
| Post subject: | Re: srxl2 AR6610T |
Well done, As you found out it needs to plug into data port and will work with the spirit through this port. But if you use a 4651T as a sat with the 6610T you will need to use port 1 to the spirit.... |
|
| Author: | Joker [ Thu 23. Apr 2020 22:05:56 ] |
| Post subject: | Re: srxl2 AR6610T |
ok, thank you for the information. but port 1 is for the gas channel right? |
|
| Author: | 10x [ Thu 23. Apr 2020 22:07:58 ] |
| Post subject: | Re: srxl2 AR6610T |
If it see's a srxl2 signal within the first 500Ms it reverts to SRXL2.. Correction from Chris: It is 200ms....not 500ms.. |
|
| Author: | Joker [ Thu 23. Apr 2020 22:49:28 ] |
| Post subject: | Re: srxl2 AR6610T |
hanks good to know
|
|
| Author: | chris_0815 [ Fri 24. Apr 2020 10:08:59 ] |
| Post subject: | Re: srxl2 AR6610T |
10x wrote: If it see's a srxl2 signal within the first 500Ms it reverts to SRXL2.. Small correction: if a device wants to communicate via SRXL2 on the throttle port, it must answer within 200 milli seconds. If a SRXL2 receiver does not get the handshake within that period, it will revert to "normal" PWM mode, see Specification for Spektrum® SRXL2. chris |
|
| Author: | HeliMLM [ Fri 24. Apr 2020 10:10:44 ] |
| Post subject: | Re: srxl2 AR6610T |
@10x... as you are 'playing around' a lot with srxl2 too... did you test failsafe? how is your experience? as i my parallel thread... i am in trouble with it not working 
|
|
| Page 7 of 12 | All times are UTC + 1 hour |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|